Prestige APS511C Key Fob Programming Instructions

This Prestige APS511C system uses replacement remote: APS2K4S50, ELVATOCAPS2K4CF50, ELVATOD

Perform steps below:

1. Turn the ignition ON. (Don’t start the engine)
2. Press the valet switch/button on – off – on – off- on then off.
3. The LED will flash once, and you’ll hear a chirp from the siren once.
4. To assign any of the 3 remote’s button functions to channel one just just perform steps below:
a) Press button #1 on the remote.
b) Press button #2 on the remote.
c) Press both buttons simultaneously on the remote.
5 Press and hold the selected choice a, b, or c above, until the siren chirps to confirm that programming the channel 1 was successful.
6. Turn the valet switch/button on then off.
7. The L. E. D. will flash twice and the siren chirps once.
8. You can assign any of the two remaining button functions listed in 4a, 4b, or 4c above to operate channel 2. You cannot use the button(s) that operate channel 1, selected in step 5 to operate channel 2.
9. Press and hold the selected choice. The siren chirps which means programming channel 2 was successful.
10. Turn the valet/bypass switch on, and then off again.
11. The dash mounted L.E.D. will flash 3 times and the siren chirps once, indicating that the system is ready to accept programming for channel 3.
12. Press and hold the remaining transmitter button function. The siren will make a long chirp to confirm that programming of channel 3 was successful.
13. Turn the ignition OFF to turn programming mode OFF.

NOTE: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds of the previous step. If the 15 second time limit expires between steps, the unit will automatically exit the program mode. This is indicated by a long chirp from the siren. Non alarm models will flash the parking lights only to confirm the transmitter code has been learned and stored. NOTE: Because the system may be capable of sounding a siren, the vehicle horn, or both, where the siren chirp is referenced below, the siren may chirp, the horn may beep, or both devices may sound.

TO PROGRAM ADDITIONAL TRANSMITTERS:

1. Enter the vehicle, and turn the ignition switch to the on position.
2. Press and release the valet push button switch three times. NOTE: Some systems may use a combination push-button LED switch. In these systems the push-button and the dash mounted LED are one and the same.
3. The dash mounted LED will flash 1x, and the siren will chirp 1x, indicating that the system is ready to accept programming of channel #1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.
4. Press and hold the lock or lock/unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. “Repeat step 4 for each transmitter you wish to program”. NOTE: If your transmitter button has the Lock/Unlock icon on one button, press and release the valet push button switch 2 times then move on to step #8.
5. Press and release the valet push button switch one time to advance to channel 2. The siren will chirp 2 times and the dash mounted LED will Flash 2 times, indicating that the unit is ready to accept programming for channel # 2 which is only used for separate lock and unlock button transmitters, and is the disarm/unlock/unlock 2 and panic.
6. Press and hold the unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. “Repeat step 6 for each transmitter you wish to program”.
7. Press and release the valet push button switch one time to advance to channel 3. The siren will chirp 3 times and the dash mounted LED will flash 3 times, indicating that the unit is ready to accept programming for channel # 3 which is the trunk release/ alternate output channel of the system.
8. Press and hold the trunk/key symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. “Repeat step 8 for each transmitter you wish to program”.
9. Press and release the valet push button switch one time to advance to channel 4 if so equipped. The siren will chirp 4 times and the dash mounted LED will Flash 4 times, indicating that the unit is ready to accept programming for channel # 4, optional device (where equipped)
10. Press and hold the Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. “Repeat step 10 for each transmitter you wish to program”.

If you can’t find your valet switch click here.

Leave a Reply

Your email address will not be published. Required fields are marked *